Goal
| # | Your goal in this lesson |
|---|---|
| 1 | Connect an electric guitar to an amp and switch off safely. |
| 2 | Dial in a clean starting setting on the amp: volume, gain, bass, middle, treble. |
| 3 | Check your sound by ear: adjust your settings while playing the 8-measure sound check twice at 70 BPM. |
Before you start
| # | Before you start, you should be able to |
|---|---|
| 1 | You know the parts of the guitar (Know your guitar). |
| 2 | You can play downstrokes on open strings and you know about pick thickness (Posture, holding the guitar and the pick). |
If you play acoustic, skim the amp section; your main work is in “Tone on acoustic” below.
Explanation
Listen first: the piece in the player is a sound check. First the low E rings (the low end), then the thin strings (the top end), then all six open strings together. While you play it, you’ll adjust your settings to these sounds.
Plugging in and switching off. Before you plug in, the amp should be off or its volume at zero; otherwise you get a loud pop from the speaker. Plug the cable into the guitar first, then the amp, switch the amp on, and raise the volume slowly. To switch off, reverse it: volume down, amp off, cable out last.
The amp’s knobs.
- Volume: how loud it is. Start low; conversation level is plenty. Protect your hearing: if your ears ring or feel tired, turn it down.
- Gain (called drive on some amps): how dirty or gritty the sound gets. Low gain is clean, high gain is distortion. For a clean sound, keep the gain low (around 9-10 o’clock).
- Bass, middle, treble: the tone balance of low, mid and high frequencies. Set them all to the middle, 12 o’clock, and adjust by ear from there. Muddy? Turn the bass down. Piercing? Turn the treble down. Thin? Bring the middle up.
- If your amp has channels, choose the clean channel. Keep effects like reverb off or very low for now so you hear yourself clearly.
- For late-night or quiet practice, you can use the amp’s headphone output.
The guitar’s knobs. To start with, turn the guitar’s volume and tone knobs all the way up and shape the sound on the amp. Pickup selector: the neck pickup sounds warm and round, the bridge pickup bright and sharp; the positions in between blend the two.
Tone on acoustic. An acoustic’s sound comes straight from the body, so you shape the tone with your hands:
| Part | What happens |
|---|---|
| The pick | a thin pick sounds soft and light when strumming; a thick pick sounds round and clear on single notes. 0.6-0.8 mm is a good middle ground to start with. |
| Where you pick | over the sound hole the sound is warm and full; near the bridge it’s bright and sharp. |
| How hard you pick | a light touch sounds soft, a hard one bright and loud. Start light. |
Tone in the player. In the player’s guitar sound menu you can switch between “Acoustic (steel string)”, “Electric, clean” and “Electric, distorted”. Listen to the same piece with all three: it’s the easiest way to hear what gain does to the sound.
Exercises
| Metronome | Repeats / time | Pass criterion |
|---|---|---|
1. Safe connection With the amp off, plug in the cable, switch the amp on and raise the volume slowly. Then switch off in order. (On acoustic: find two different sounds by picking over the sound hole and near the bridge.) | ||
| — | Time: 2 minutes, twice. | there’s no pop from the speaker and you know the order by heart. |
2. Starting setting Volume low, gain low, bass-middle-treble at 12 o’clock, guitar volume and tone fully up. Loop measures 1-4 and adjust by ear while you play. | ||
| 60 BPM. | 4 rounds; touch only one knob per round. | the low end isn’t muddy, the highs don’t pierce, and all six strings ring in balance. |
3. Pickup or hand-position comparison Loop measures 5-8. Play one round on the neck pickup and one on the bridge pickup (on acoustic: one round over the sound hole, one near the bridge). | ||
| 60 → 70 BPM. | 2 rounds at each tempo. | you can describe the difference: which one is warm, which one is bright. |
4. The full sound check Play all 8 measures; once your settings feel right, write them down. | ||
| 60 → 70 → 80 BPM. | 2 rounds at 70 BPM; if you’re ready, 1 round at 80 BPM. | two clean rounds at 70 BPM and a starting setting written down. |
Common mistakes
| Symptom | Cause | Fix |
|---|---|---|
| A loud pop from the speaker when you plug in | you’re connecting with the amp on and the volume up | turn the volume to zero or switch the amp off first, then plug in. |
| The amp is on but there’s no sound | the guitar’s volume knob is down or the cable isn’t fully in | turn the guitar’s volume up and push the cable all the way in at both ends. |
| The sound isn’t clean, it’s fuzzy | the gain is too high | bring the gain down to 9-10 o’clock. |
| The sound is muffled and dull | the guitar’s tone knob is down or the treble is too low | turn the tone fully up and set the treble to 12 o’clock. |
| The amp hums all the time | high gain or a loose cable | lower the gain and check the cable; mute the strings with your hand when you’re not playing. |
| Your ears ring | the volume is too high | turn it down; conversation level is enough for practice. |
Checklist
| I can do it | Item |
|---|---|
| I can connect and switch off the amp without a pop. | |
| I know what volume, gain, bass, middle and treble do. | |
| I can dial in a clean starting setting and adjust it by ear. | |
| I can hear the difference between the neck and bridge pickups (or hand positions on acoustic). | |
| I can play the sound check twice cleanly at 70 BPM. |
The lessons you mark and the concepts you see are stored only in this browser; no account. Your path